СИСТЕМА ECD, Diagnostic DTC:P0489, P0490

DTC Code DTC Name
P0489 Exhaust Gas Recirculation Control Circuit Low
P0490 Exhaust Gas Recirculation Control Circuit High

DESCRIPTION

The EGR actuator is operated by the ECM and opens and closes the EGR valve using gears. The opening angle of the EGR valve is detected by the EGR position sensor, which is mounted on the electric EGR control valve assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0489 Exhaust Gas Recirculation Control Circuit Low The EGR actuator current is below 0.5 A for 2.0 seconds during EGR valve operation (1 trip detection logic).
  • Open or short in EGR valve circuit

  • Electric EGR control valve assembly

  • ECM

Comes on DTC stored
P0490 Exhaust Gas Recirculation Control Circuit High An EGR actuator current of 8 A or higher due to a mechanical malfunction, or a hall IC temperature of 150 to 160°C (302 to 320°F) or higher is detected (1 trip detection logic).
  • Open or short in EGR valve circuit

  • Electric EGR control valve assembly

  • ECM

Comes on DTC stored
Table 1. Related Data List
DTC No. Data List
P0489
  • Actual EGR Valve Pos.

  • Target EGR Position

P0490

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0489 Idle the engine for 5 seconds or more
P0490

WIRING DIAGRAM

Refer to DTC P042E.

Click hereНажмите здесь

CAUTION / NOTICE / HINT

Note:

After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click hereНажмите здесь).

Tip:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

    1. Inspect the electric EGR control valve assembly.

      Click hereНажмите здесь

      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  2. CHECK HARNESS AND CONNECTOR (ELECTRIC EGR CONTROL VALVE ASSEMBLY - ECM)

    1. Disconnect the electric EGR control valve assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      p1-5 (M+) - B164-86 (EGM+) Always Below 1 Ω
      p1-1 (M-) - B164-85 (EGM-) Always Below 1 Ω
      p1-5 (M+) or B164-86 (EGM+) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  3. REPLACE ECM

    1. Replace the ECM.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 5


  4. REPAIR OR REPLACE HARNESS OR CONNECTOR

    1. Repair or replace the harness or connector.

      Result
      Proceed to
      NEXT
    NEXT
  5. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs
    5. Turn the ignition switch off for 30 seconds or more.

    6. Start the engine.

    7. Idle the engine for 5 seconds or more

    8. Turn the GTS on.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    10. Confirm that the DTC is not output.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT
    NEXT

    END


  6. REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY

    1. Replace the electric EGR control valve assembly.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 5