ПЕРЕДНИЙ САЛЬНИК КОЛЕНЧАТОГО ВАЛА УСТАНОВКА

PROCEDURE

  1. INSTALL TIMING CHAIN COVER OIL SEAL

    1. Apply MP grease to a new timing chain cover oil seal lip.

      Note:

      Keep the lip free from foreign matter.

    2. Using SST and a hammer, tap in the new timing chain cover oil seal until its surface is flush with the timing chain cover sub-assembly.

      A012FJAN01
      SST
      09223-22010
      Oil seal tap in depth
      -1.0 to 0 mm (-0.0394 to 0 in.)
      Note:
      • Do not tap in the timing chain cover oil seal at an angle.

      • Wipe off excess grease from the crankshaft.

  2. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY

    1. Align the key with the key groove of the crankshaft damper sub-assembly, and install the crankshaft damper sub-assembly to the crankshaft.

    2. Using SST, hold the crankshaft damper sub-assembly.

      A012IWSC02
      *a Hold
      *b Turn
      SST
      09213-58014
      09330-00021
    3. Tighten the bolt to the specified torque.

      Момент затяжки
      210 N*m  { 2141 kgf*cm, 155 ft.*lbf }
  3. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

    1. Set the engine mounting insulator RH sub-assembly onto the vehicle and engine mouthing bracket RH.

    2. Install the engine mounting insulator sub-assembly RH with the 3 bolts and 3 nuts.

      Момент затяжки
      Bolt
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
      Nut A
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
      Nut B
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }
      A012MAPN01
    3. Connect the cooler pipe clamp to the engine mounting insulator sub-assembly RH.

    4. Install the cooler pipe clamp bracket with the bolt.

      Момент затяжки
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }
  4. INSTALL RADIATOR RESERVE TANK ASSEMBLY

    1. Install the radiator reserve tank assembly with the 2 bolts.

      Момент затяжки
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
  5. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    1. Using a vernier caliper, measure the free length of the compression springs.

      A012KJV
      Minimum 41.5 mm (1.63 in.)
      Tip:

      If the free length is less than the minimum, replace the compression spring.

    2. Using a plastic hammer and wooden block, tap in a new gasket until its surface is flush with the No. 2 exhaust manifold converter sub-assembly.

      A012GTAC48
      *1 No. 2 Exhaust Manifold Converter Sub-assembly
      *2 Gasket
      *a Wooden Block
      Note:
      • Be careful with the installation direction of the gasket.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • Do not push in the gaskets by using the front exhaust pipe sub-assembly when connecting it.

    3. Install the front exhaust pipe assembly to the No. 2 exhaust manifold converter sub-assembly with the 2 bolts and 2 compression springs.

      A012ICYC01
      *1 No. 2 Exhaust Manifold Converter Sub-assembly
      *2 Front Exhaust Pipe Assembly
      *3 Gasket
      *a Space Between Flanges: 8.5 mm (0.335 in.)
      Момент затяжки
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }
      Tip:

      After installation, check that the space between the flanges of the No. 2 exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.

  6. INSTALL FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT (w/ Reinforcement)

    Click hereНажмите здесь

  7. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

    Click hereНажмите здесь

  8. INSTALL V-RIBBED BELT

    Click hereНажмите здесь

  9. INSPECT FOR OIL LEAK

  10. INSTALL NO. 1 ENGINE COVER (w/ No. 1 Engine Cover)

    Click hereНажмите здесь

  11. INSTALL REAR ENGINE UNDER COVER RH

    Click hereНажмите здесь

  12. INSTALL NO. 1 ENGINE UNDER COVER

    Click hereНажмите здесь

  13. INSTALL FRONT WHEEL RH

    Момент затяжки
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }