СИСТЕМА ECD, Diagnostic DTC:P0522, P0523

DTC Code DTC Name
P0522 Engine Oil Pressure Sensor / Switch Low
P0523 Engine Oil Pressure Sensor / Switch High

DESCRIPTION

Refer to DTC P0524.

Click hereНажмите здесь

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0522 Engine Oil Pressure Sensor / Switch Low

Conditions (a) and (b) continue for 5 seconds or more (1 trip detection logic):

(a) Ignition switch is ON.

(b) Oil pressure sender gauge assembly voltage is 0.05 V or less.

  • Open or short in oil pressure sender gauge assembly circuit

  • Oil pressure sender gauge assembly

  • ECM

Does not come on DTC stored
P0523 Engine Oil Pressure Sensor / Switch High

Conditions (a) and (b) continue for 5 seconds or more (1 trip detection logic):

(a) Ignition switch is ON.

(b) Oil pressure sender gauge assembly voltage is 4.6 V or higher.

  • Open or short in oil pressure sender gauge assembly circuit

  • Oil pressure sender gauge assembly

  • ECM

Does not come on DTC stored
Table 1. Related Data List
DTC No. Data List

P0522

P0523

Engine Oil Pressure

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0522 Idling for 5 second
P0523

WIRING DIAGRAM

A012HW9E01

CAUTION / NOTICE / HINT

Note:
  • Inspect the fuses of circuits related to this system before performing the following procedure.

  • After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click hereНажмите здесь).

Tip:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENDER GAUGE ASSEMBLY - ECM)

    1. Disconnect the oil pressure sender gauge assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B153-3 (VC) - B164-93 (VPOP) Always Below 1 Ω
      B153-2 (VOUT) - B164-116 (POP) Always Below 1 Ω
      B153-1 (GND) - B164-70 (EPOP) Always Below 1 Ω
      B153-3 (VC) or B164-93 (VPOP) - Body ground Always 10 kΩ or higher
      B153-2 (VOUT) or B164-116 (POP) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  2. CHECK TERMINAL VOLTAGE (POWER SOURCE OF OIL PRESSURE SENDER GAUGE ASSEMBLY)

    1. Disconnect the oil pressure sender gauge assembly connector.

      A012LHTC03
      *a

      Front view of wire harness connector

      (to Oil Pressure Sender Gauge Assembly)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below

      Standard Voltage
      Tester Connection Condition Specified Condition
      B153-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    GO TO STEP 5


    OK
  3. REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

    1. Replace the oil pressure sender gauge assembly.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT
  4. CHECK WHETHER DTC OUTPUT RECURS (DTC P0522 OR P0523)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs
    5. Turn the ignition switch off for 30 seconds or more.

    6. Start the engine and idle it for 5 second or more.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      ResultProceed to
      DTC P0522 or P0523 is outputA
      DTC is not outputB
    B

    END


    A
  5. REPLACE ECM

    1. Replace the ECM.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 7


  6. REPAIR OR REPLACE HARNESS OR CONNECTOR

    1. Repair or replace the harness or connector.

      Result
      Proceed to
      NEXT
    NEXT
  7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs
    5. Turn the ignition switch off for 30 seconds or more.

    6. Start the engine and idle it for 5 second or more.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Confirm that the DTC is not output.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT
    NEXT

    END