ПРИВОД ВЫБОРА И ПЕРЕКЛЮЧЕНИЯ ПЕРЕДАЧ УСТАНОВКА

PROCEDURE

  1. INSTALL SHIFT AND SELECT ACTUATOR ASSEMBLY

    1. Install the breather plug cap to the shift and select actuator assembly.

    2. Install the breather protector to the shift and select actuator assembly with the bolt.

      Момент затяжки
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    3. Using a plastic hammer, tap in 2 new ring pins to the specified protrusion height.

      A012HJ5
      Protrusion Height
      5.2 to 5.8 mm (0.205 to 0.228 in.)
    4. Clean and degrease the contact surfaces between the shift and select actuator and front transaxle case.

    5. Apply FIPG to the shift and select actuator as shown illustration.

      A012N8BC03
      *a FIPG
      *b Seal Diameter 1.2 mm (0.0472 in.)
      FIPG
      Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent.
      Note:
      • Remove any oil from the contact surfaces.

      • Install the parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.

    6. When replacing the shift and select actuator with a new one:

      1. Move the inner select lever as shown in the illustration.

        A012MSP
      2. Install the shift and select actuator and wire harness clamp bracket to the front transaxle case with the 6 bolts.

        A012MBBC02
        *a Shift and Select Lever Shaft Head
        *b Shift Actuator Plate
        *c Select Actuator Plate
        *d Inner Select Lever
        Момент затяжки
        18 N*m  { 184 kgf*cm, 13 ft.*lbf }
        Note:
        • Securely engage the shift actuator plate to the shift and select lever shaft head.

        • Securely engage the select actuator plate to the inner select lever.

    7. When reusing the shift and select actuator:

      1. Install the shift and select actuator to the front transaxle case with the 6 bolts.

        A012FP7C02
        *a Shift and Select Lever Shaft Head
        *b Shift Actuator Plate
        *c Select Actuator Plate
        *d Inner Select Lever
        Момент затяжки
        18 N*m  { 184 kgf*cm, 13 ft.*lbf }
        Note:
        • Securely engage the shift actuator plate to the shift and select lever shaft head.

        • Securely engage the select actuator plate to the inner select lever.

    8. Install the wire harness clamp bracket to the shift and select actuator with the bolt.

      Момент затяжки
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
    9. Install the wire harness clamp bracket to the shift and select actuator with the bolt.

      Момент затяжки
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
  2. CONNECT WIRE HARNESS

    1. Connect the connector and 3 wire harness clamps.

    2. Connect the 6 connectors.

    3. Connect the 5 wire harness clamps.

  3. INSTALL NO. 1 AIR TUBE

    1. Install the No. 1 air tube and tighten the 2 hose clamps.

      A012GM2C01
      *a Hose Clamp
      Момент затяжки
      6.5 N*m  { 66 kgf*cm, 58 in.*lbf }
      Note:

      One minute after tightening the hose clamps, check that residual torque is 3.2 N*m (33 kgf*cm, 28 in.*lbf) or more.

    2. Install the 4 bolts.

      Момент затяжки
      Bolt A
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
      Bolt B
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
      Bolt C
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }
    3. Connect the wire harness clamp.

  4. INSTALL AIR CLEANER BRACKET

    Click here Нажмите здесь

  5. INSTALL FUEL FILTER SUPPORT

    Click here Нажмите здесь

  6. CONNECT ENGINE WIRE

    Click hereНажмите здесь

  7. INSTALL FUEL FILTER ASSEMBLY

    Click hereНажмите здесь

  8. INSTALL BATTERY

    Click here Нажмите здесь

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here Нажмите здесь

  10. PERFORM INITIALIZATION OF MULTI-MODE MANUAL TRANSAXLE SYSTEM

    Click hereНажмите здесь

  11. PERFORM LEARNING OF MULTI-MODE MANUAL TRANSAXLE SYSTEM

    Click hereНажмите здесь

  12. PERFORM SYNCHRONIZATION POSITION CALIBRATION

    Click hereНажмите здесь