ПЕРЕДНИЙ ПРИВОДНОЙ ВАЛ В СБОРЕ (для моделей с 1AD-FTV) РАЗБОРКА

PROCEDURE

  1. SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

    1. Hold the drive shaft in a vise between aluminum plates.

      Note:

      Do not overtighten the vise.

    2. Using needle-nose pliers, separate the front No. 2 axle inboard joint boot clamp.

      A012FZR
  2. SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

    1. Using pliers, separate the front axle inboard joint boot clamp as shown in the illustration.

      A012HEC
  3. SEPARATE FRONT AXLE INBOARD JOINT BOOT

    1. Separate the front axle inboard joint boot from the front drive inboard joint assembly.

  4. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

    1. Remove the old grease from the front drive inboard joint assembly.

    2. Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

      A012GLPC03
      *a Matchmark
      Note:

      Do not use a punch for the marks.

    3. Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.

    4. Hold the drive shaft in a vise between aluminum plates.

      Note:

      Do not overtighten the vise.

    5. Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.

      A012MXJ
    6. Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

      A012KXWC04
      *a Matchmark
      Note:

      Do not use a punch for the marks.

    7. Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

      Note:
      • Do not tap the rollers.

      • Do not drop the tripod joint.

  5. REMOVE FRONT AXLE INBOARD JOINT BOOT

    1. Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.

  6. REMOVE FRONT DRIVE SHAFT DAMPER LH (w/ Drive Shaft Damper)

    1. Using pliers, remove the front drive shaft damper clamp.

      A012M9S
    2. Remove the front drive shaft damper LH.

  7. SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

    1. Using pliers, separate the front No. 2 axle outboard joint boot clamp.

      A012IB7
  8. SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

    Tip:

    Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.

  9. REMOVE FRONT AXLE OUTBOARD JOINT BOOT

    1. Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.

    2. Remove the old grease from the outboard joint.

  10. REMOVE FRONT DRIVE SHAFT DUST COVER LH

    1. Using SST and a press, remove the front drive shaft dust cover LH.

      A012GO0N02
      SST
      09950-00020
      Note:
      • Be careful not to drop the front drive inboard joint assembly.

      • Do not overtighten SST.

  11. REMOVE FRONT DRIVE SHAFT DUST COVER RH

    1. Using a press, remove the front drive shaft dust cover RH.

      A012MOJ
      Note:

      Be careful not to drop the front drive inboard joint assembly.

  12. REMOVE DRIVE SHAFT BEARING CASE SNAP RING (for RH Side)

    1. Hold the drive shaft in a vise between aluminum plates.

      Note:

      Do not overtighten the vise.

    2. Using a screwdriver, separate the drive shaft bearing case snap ring from the drive shaft bearing case sub-assembly.

      A012I1Y
  13. REMOVE DRIVE SHAFT BEARING CASE SUB-ASSEMBLY (for RH Side)

    1. Using a press, remove the drive shaft bearing case sub-assembly from the front drive inboard joint assembly.

      Note:

      Do not drop the front drive inboard joint assembly.

      A012J28
  14. REMOVE FRONT DRIVE SHAFT DUST COVER (for RH Side)

    1. Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly.

      SST
      09950-00020
      Note:

      Do not drop the front drive inboard joint assembly.

      A012IT6N01
  15. REMOVE FRONT DRIVE SHAFT BEARING (for RH Side)

    1. Using a snap ring expander, remove the snap ring.

      A012KCI
    2. Using SST and a press, remove the front drive shaft bearing from the front drive inboard joint assembly.

      SST
      09527-10011
      A012HW0N02
    3. Remove the drive shaft bearing case snap ring.