СИСТЕМА ECD, Diagnostic DTC:P0704

DTC Code DTC Name
P0704 Clutch Switch Input Circuit Malfunction

DESCRIPTION

The clutch switch is mounted on the clutch pedal. The switch is turned off when depressing the clutch pedal, and transmits a signal to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0704 Clutch Switch Input Circuit Malfunction

No clutch switch signals to ECM despite gears being shifted.

(2 trip detection logic)

  • Open or short in No. 2 clutch pedal switch assembly circuit

  • No. 2 clutch pedal switch assembly

  • ECM

Comes on DTC stored
Table 1. DTC Detection Drive Pattern
DTC No. DTC Detection Drive Pattern
P0704 Gears are shifted more than 10 times

WIRING DIAGRAM

A012HOHE01

CAUTION / NOTICE / HINT

Note:
  • When replacing the ECM, perform ECM Initialization and Registration.

    Click here Нажмите здесь

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tip:
  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing a new ECM, perform all of the initialization and registration procedures for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK NO. 2 CLUTCH PEDAL SWITCH ASSEMBLY

    1. Check installation of the No. 2 clutch pedal switch assembly.

      Click hereНажмите здесь

      OK
      No. 2 clutch pedal switch assembly is installed correctly.
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  2. INSPECT NO. 2 CLUTCH PEDAL SWITCH ASSEMBLY

    1. Inspect the No. 2 clutch pedal switch assembly.

      Click hereНажмите здесь

      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  3. CHECK HARNESS AND CONNECTOR (NO. 2 CLUTCH PEDAL SWITCH ASSEMBLY - ECM)

    1. Disconnect the No. 2 clutch pedal switch assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A4-2 (CL-) - A101-5 (D) Always Below 1 Ω
      A4-2 (CL-) or A101-5 (D) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  4. CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 2 CLUTCH PEDAL SWITCH ASSEMBLY)

    1. Disconnect the No. 2 clutch pedal switch assembly connector.

      A012LXTC04
      *a

      Front view of wire harness connector

      (to No. 2 Clutch Pedal Switch Assembly)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A4-1 (CL+) - Body ground Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  5. REPLACE ECM

    1. Replace the ECM.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT
  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs
    4. Start the engine.

    5. Change the shift more than 10 times during city driving.

    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

    7. Confirm that the pending DTC is not output again.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT
    NEXT

    END


  7. REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN RELAY - NO.2 CLUTCH PEDAL SWITCH ASSEMBLY)

    Result
    Proceed to
    NEXT
    NEXT Нажмите здесь

    GO TO STEP 6


  8. REPAIR OR REPLACE HARNESS OR CONNECTOR

    Result
    Proceed to
    NEXT
    NEXT Нажмите здесь

    GO TO STEP 6


  9. REPLACE NO. 2 CLUTCH PEDAL SWITCH ASSEMBLY

    1. Replace the No. 2 clutch pedal switch assembly.

      Click here Нажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 6


  10. SECURELY NO. 2 CLUTCH PEDAL SWITCH ASSEMBLY

    1. Securely reinstall the No. 2 clutch pedal switch assembly.

      Click here Нажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 6