СИСТЕМА ECD, Diagnostic DTC:P0560

DTC Code DTC Name
P0560 System Voltage

DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage The voltage at terminal BATT drops excessively for 3 seconds and part of the stored values in the ECM are initialized (1 trip detection logic).
  • Open in back up power source circuit (to BATT terminal)

  • Battery

  • Battery terminals

  • ECM

Comes on DTC stored
Table 1. Related Data List
DTC No. Data List
P0560 Battery Voltage*

*: This is not the voltage of the BATT, it is the power supply voltage for the ECM.

Tip:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partially cleared.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0560 Ignition switch ON for 3 seconds

WIRING DIAGRAM

A012JDTE01
Table 2.
*a FL MAIN
*b EFI-MAIN

CAUTION / NOTICE / HINT

Note:
  • Inspect the fuses of circuits related to this system before performing the following procedure.

  • After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click hereНажмите здесь).

Tip:
  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

  • When the ignition switch is turned to ON, even though +B voltage is present, when the voltage at terminal BATT (power supply for maintaining memorized values in the ECM) drops excessively, this DTC is stored.

PROCEDURE

  1. CHECK TERMINAL VOLTAGE (BATT VOLTAGE)

    1. Disconnect the ECM connector.

      A012KUQC02
      *a

      Front view of wire harness connector

      (to ECM)

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A118-2 (BATT) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  2. INSPECT BATTERY

    1. Check that the battery is not depleted.

      OK
      Battery is not depleted.
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  3. CHECK BATTERY TERMINAL

    1. Check that the battery terminals are not loose or corroded.

      OK
      Battery terminals are not loose or corroded.
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  4. CHECK WHETHER DTC OUTPUT RECURS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs
    4. Turn the ignition switch off.

    5. Turn the ignition switch to ON for 3 seconds.

    6. Turn the GTS on.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    8. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      ResultProceed to
      DTC P0560 is outputA
      DTC is not outputB
    B

    END


    A
  5. REPLACE ECM

    1. Replace the ECM.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 7


  6. REPAIR OR REPLACE BATTERY TERMINAL

    1. Repair or replace the battery terminal.

      Result
      Proceed to
      NEXT
    NEXT
  7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs
    5. Turn the ignition switch off for 30 seconds or more.

    6. Turn the ignition switch to ON for 3 seconds.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Confirm that the DTC is not output.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT
    NEXT

    END


  8. RECHARGE OR REPLACE BATTERY

    1. Recharge or replace the battery.

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 7


  9. REPAIR OR REPLACE HARNESS OR CONNECTOR

    1. Repair or replace the harness or connector.

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 7