ВЫХОДНОЙ ВАЛ ПРОВЕРКА

PROCEDURE

  1. INSPECT 1ST GEAR THRUST CLEARANCE

    1. Using a dial indicator, measure the 1st gear thrust clearance.

      A012HS2
      Standard Clearance
      0.20 to 0.38 mm (0.00787 to 0.0150 in.)
      Maximum Clearance
      0.38 mm (0.0150 in.)

      If the clearance exceeds the maximum, replace the No. 1 transmission clutch hub, 1st gear bush or 1st gear.

  2. INSPECT 2ND GEAR THRUST CLEARANCE

    1. Using a dial indicator, measure the 2nd gear thrust clearance.

      A012J13
      Standard Clearance
      0.15 to 0.33 mm (0.00591 to 0.0130 in.)
      Maximum Clearance
      0.33 mm (0.0130 in.)

      If the clearance exceeds the maximum, replace the inner 2nd gear bearing race, No. 1 transmission clutch hub, 2nd gear or 3rd driven gear.

  3. INSPECT 1ST GEAR RADIAL CLEARANCE

    1. Using a dial indicator, measure the 1st gear radial clearance.

      A012G46
      Standard Clearance
      0.009 to 0.047 mm (0.000354 to 0.00185 in.)
      Maximum Clearance
      0.047 mm (0.00185 in.)

      If the clearance exceeds the maximum, replace the 1st gear, 1st gear needle roller bearing or output shaft.

  4. INSPECT 2ND GEAR RADIAL CLEARANCE

    1. Using a dial indicator, measure the 2nd gear radial clearance.

      A012KQ6
      Standard Clearance
      0.009 to 0.047 mm (0.000354 to 0.00185 in.)
      Maximum Clearance
      0.047 mm (0.00185 in.)

      If the clearance exceeds the maximum, replace the 2nd gear, 2nd gear needle roller bearing or output shaft.

  5. INSPECT OUTPUT SHAFT

    1. Using a dial indicator and 2 V-blocks, check the output shaft runout.

      A012MLX
      Maximum Runout
      0.015 mm (0.000591 in.)

      If the runout exceeds the maximum, replace the output shaft.

    2. Using a micrometer, measure the outer diameter of the output shaft journal surface at the locations indicated.

      A012N1FN05
      Standard Outer Diameter
      Location A
      30.002 to 32.017 mm (1.1812 to 1.2605 in.)
      Location B
      37.990 to 38.000 mm (1.49566 to 1.49606 in.)
      Location C
      40.790 to 40.800 mm (1.60590 to 1.60629 in.)
      Location D
      28.002 to 28.017 mm (1.10243 to 1.10302 in.)
      Minimum Outer Diameter
      Location A
      30.002 mm (1.1812 in.)
      Location B
      37.990 mm (1.49566 in.)
      Location C
      40.790 mm (1.60590 in.)
      Location D
      28.002 mm (1.10243 in.)

      If outer diameters of any location is less than the minimum, replace the output shaft.

  6. INSPECT 1ST GEAR

    1. Using a cylinder gauge, measure the inside diameter of the 1st gear.

      A012LHJ
      Standard Inside Diameter
      52.909 to 52.925 mm (2.08302 to 2.08365 in.)
      Maximum Inside Diameter
      52.925 mm (2.08365 in.)

      If the inside diameter exceeds the maximum, replace the 1st gear.

  7. INSPECT 2ND GEAR

    1. Using a cylinder gauge, measure the inside diameter of the 2nd gear.

      A012MJH
      Standard Inside Diameter
      52.909 to 52.925 mm (2.08302 to 2.08365 in.)
      Maximum Inside Diameter
      52.925 mm (2.08365 in.)

      If the inside diameter exceeds the maximum, replace the 2nd gear.

  8. INSPECT 1ST GEAR BUSHING

    1. Using a micrometer, measure the outer diameter of the 1st gear bushing.

      A012GW4
      Standard Outer Diameter
      47.89 to 47.90 mm (1.88542 to 1.88582 in.)
      Minimum Outer Diameter
      47.89 mm (1.88542 in.)

      If the outer diameter is less than the minimum, replace the 1st gear bushing.

    2. Using a cylinder gauge, measure the inside diameter of the 1st gear bushing.

      A012LFY
      Standard Inside Diameter
      40.805 to 40.820 mm (1.60649 to 1.60708 in.)
      Maximum Inside Diameter
      40.820 mm (1.60708 in.)

      If the inside diameter exceeds the maximum, replace the 1st gear bushing.

  9. INSPECT INNER 2ND GEAR BEARING RACE

    1. Using a micrometer, measure the outer diameter of the inner 2nd gear bearing race.

      A012NB4
      Standard Outer Diameter
      47.89 to 47.90 mm (1.88542to 1.88582in.)
      Minimum Outer Diameter
      47.89 mm (1.88542 in.)

      If the outer diameter is less than the minimum, replace the inner 2nd gear bearing race.

    2. Using a cylinder gauge, measure the inside diameter of the inner 2nd gear bearing race.

      A012HYI
      Standard Inside Diameter
      38.005 to 38.020 mm (1.49625 to 1.49684 in.)
      Maximum Inside Diameter
      38.020 mm (1.49684 in.)

      If the inside diameter exceeds the maximum, replace the inner 2nd gear bearing race.

  10. INSPECT NO. 1 SYNCHRONIZER RING SET (for 1st Gear)

    1. Coat the 1st gear cone and No. 1 synchronizer ring set (inner ring, middle ring and outer ring) with gear oil.

    2. Install the inner ring to the 1st gear.

      A012M35C09
      *a Outer Ring
      *b Middle Ring
      *c Inner Ring
    3. Install the middle ring to the 1st gear.

    4. Install the outer ring to the 1st gear.

    5. Check for wear and damage.

      A012MQ5C02
      *a Locks
    6. Turn the synchronizer ring set in one direction while pushing it against the 1st gear cone.

    7. Check that the synchronizer ring set locks.

      If the synchronizer ring set does not lock, replace the synchronizer ring set.

    8. Using a feeler gauge, measure the clearance between the synchronizer ring and the gear spline end.

      A012LTP
      Standard Clearance
      0.915 to 1.855 mm (0.03602 to 0.07303 in.)
      Minimum Clearance
      0.915 mm (0.03602 in.)

      If the clearance is less than the minimum, replace the synchronizer ring set.

  11. INSPECT NO. 1 SYNCHRONIZER RING SET (for 2nd Gear)

    1. Coat the 2nd gear cone and No. 1 synchronizer ring set (for 2nd gear) (inner ring, middle ring and outer ring) with gear oil.

    2. Install the inner ring to the 2nd gear.

      A012GVLC05
      *a Outer Ring
      *b Middle Ring
      *c Inner Ring
    3. Install the middle ring to the 2nd gear.

    4. Install the outer ring to the 2nd gear.

    5. Check for wear and damage.

      A012L68C02
      *a Locks
    6. Turn the synchronizer ring set in one direction while pushing it against the 2nd gear cone.

    7. Check that the synchronizer ring set locks.

      If the synchronizer ring set does not lock, replace the synchronizer ring set.

    8. Using a feeler gauge, measure the clearance between the synchronizer ring and the gear spline end.

      A012I97
      Standard Clearance
      0.92 to 1.86 mm (0.0362 to 0.0732 in.)
      Minimum Clearance
      0.92 mm (0.0362 in.)

      If the clearance is less than the minimum, replace the synchronizer ring set.

  12. INSPECT REVERSE GEAR

    1. Using a vernier caliper, measure the width of the reverse gear groove (A) and the thickness of the claw part on the No. 1 gear shift fork shaft assembly (B), and calculate the clearance.

      A012IEWC02
      *a Clearance
      Standard Clearance (A - B)
      0.1 to 0.5 mm (0.00394 to 0.0197 in.)

      If the clearance is out of specification, replace the reverse gear and No. 1 gear shift fork shaft assembly.

  13. INSPECT NO. 1 TRANSMISSION CLUTCH HUB

    1. Check that the No. 1 transmission clutch hub and reverse gear slide smoothly.

      A012IEP
    2. Check that the edges of the reverse gear splines are not worn down.