СИСТЕМА ECD, Diagnostic DTC:P0627

DTC Code DTC Name
P0627 Fuel Pump Control Circuit / Open

DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0627 Fuel Pump Control Circuit / Open Even though the CPU (command area inside ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic).
  • Open or short in suction control valve circuit

  • Suction control valve

  • ECM

Comes on DTC stored
Table 1. Related Data List
DTC No. Data List
P0627

Fuel Press

Target Common Rail Pressure

Tip:
  • For more information on the supply pump assembly (suction control valve) and common rail system, refer to the System Description.

    Click hereНажмите здесь

  • When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / All Data / Fuel Press.

    Under a stable operating condition such as idling, Fuel Press is within +/-5000 kPa of Target Common Rail Pressure.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0627 Idling for 1 second

WIRING DIAGRAM

Refer to DTC P0088.

Click hereНажмите здесь

CAUTION / NOTICE / HINT

Note:
Tip:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. INSPECT SUCTION CONTROL VALVE

    1. Disconnect the suction control valve connector.

      A012IKFC03
      *1 Supply Pump Assembly
      *2 Suction Control Valve
      *a

      Component without harness connected

      (Suction Control Valve)

    2. Measure the resistance of the suction control valve.

      OK
      No open or short circuit malfunction.
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  2. CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

    1. Disconnect the suction control valve connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B148-1 - B164-41 (PCV+) Always Below 1 Ω
      B148-2 - B164-81 (PCV-) Always Below 1 Ω
      B148-1 or B164-41 (PCV+) - Body ground Always 10 kΩ or higher
      B148-2 or B164-81 (PCV-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK
  3. CHECK WHETHER DTC OUTPUT RECURS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs
    4. Start the engine and idle it for 1 second or more.

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    7. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      ResultProceed to
      DTC is not outputA
      DTC P0627 is outputB
    A

    END


    B
  4. REPLACE ECM

    1. Replace the ECM.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 6


  5. REPAIR OR REPLACE HARNESS OR CONNECTOR

    1. Repair or replace the harness or connector.

      Result
      Proceed to
      NEXT
    NEXT
  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs
    5. Turn the ignition switch off for 30 seconds or more.

    6. Start the engine and idle it for 1 second or more.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Confirm that the DTC is not output.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT
    NEXT

    END


  7. REPLACE SUCTION CONTROL VALVE

    1. Replace the suction control valve.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT
  8. BLEED AIR FROM FUEL SYSTEM

    1. Bleed the air from the fuel system.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT
  9. PERFORM SUPPLY PUMP INITIALIZATION

    1. Perform the supply pump initialization.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 6