СИСТЕМА ECD, Diagnostic DTC:P0563

DTC Code DTC Name
P0563 System Voltage High

DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage is 17 V or higher, the ECM determines that there is a malfunction in the power supply circuit. Then the ECM illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0563 System Voltage High

Battery voltage is 17 V or higher.

(1 trip detection logic)

  • Generator

  • Battery (If 24 V battery is installed)

  • ECM

Comes on DTC stored
Table 1. DTC Detection Drive Pattern
DTC No. DTC Detection Drive Pattern
P0563 Ignition switch ON for 20 seconds or more
Table 2. Related Data List
DTC No. Data List
P0563 Battery Voltage
Tip:

If DTC P0563 is stored, the ECM does not store other DTCs or the data stored in the ECM is partially cleared.

CAUTION / NOTICE / HINT

Note:

When replacing the ECM, perform ECM Initialization and Registration.

Click here Нажмите здесь

Tip:
  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing a new ECM, perform all of the initialization and registration procedures for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK AND REPAIR CHARGING SYSTEM

    1. Check and repair the charging system.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT
  2. INSPECT BATTERY

    1. Check that the correct battery is installed.

      OK
      Correct battery is installed.
      Note:

      If a 24 V battery is installed, DTC P0563 will be stored.

      Result
      Proceed to
      NEXT
    NEXT
  3. CHECK WHETHER DTC OUTPUT RECURS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs
    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON and wait for 20 seconds or more.

    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    7. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      ResultProceed to
      DTC P0563 is outputA
      DTC is not outputB
    B

    END


    A
  4. REPLACE ECM

    1. Replace the ECM.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT
  5. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs
    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON and wait for 20 seconds or more.

    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    7. Confirm that the DTC is not output again.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT
    NEXT

    END