МЕХАНИЧЕСКАЯ ТРАНСМИССИЯ "MULTIMODE" В СБОРЕ УСТАНОВКА

CAUTION / NOTICE / HINT

Note:

When the multi-mode manual transaxle assembly is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.

PROCEDURE

  1. INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

    1. Coat a new O-ring with gear oil.

    2. Install the new O-ring to the speedometer driven hole cover sub-assembly.

    3. Install the speedometer driven hole cover sub-assembly to the transaxle case with the bolt.

      Момент затяжки
      11.3 N*m  { 115 kgf*cm, 8 ft.*lbf }
  2. INSTALL WIRE HARNESS CLAMP BRACKET

    1. Install the 3 wire harness clamp brackets with the 3 bolts.

      Момент затяжки
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
  3. INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

    Click hereНажмите здесь

  4. REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

    Click hereНажмите здесь

  5. INSPECT CLUTCH PIPE LINE

    Click hereНажмите здесь

  6. INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

    Click hereНажмите здесь

  7. INSTALL NO. 1 CLUTCH ACTUATOR BRACKET

    1. Temporarily install the No. 1 clutch actuator bracket with the bolt*1.

      A012KFGN01
    2. Temporarily install the No. 1 clutch actuator bracket with the 3 bolts.

    3. Fully install the 4 bolts in the sequence shown in the illustration.

      A012MZ1N01
      Момент затяжки
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }
  8. INSTALL CLUTCH ACTUATOR ASSEMBLY

    Click hereНажмите здесь

  9. INSTALL REAR ENGINE MOUNTING BRACKET

    1. Install the rear engine mounting bracket with the 4 bolts.

      Момент затяжки
      45 N*m  { 459 kgf*cm, 33 ft.*lbf }
  10. INSTALL FRONT ENGINE MOUNTING BRACKET

    1. Install the front engine mounting bracket with the 4 bolts.

      Момент затяжки
      for Green Bolt
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }
      for Silver Bolt
      45 N*m  { 459 kgf*cm, 33 ft.*lbf }
  11. INSTALL ENGINE MOUNTING BRACKET LH

    1. Apply sealant to the 4 bolts.

      Sealant
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
    2. Install the engine mounting bracket LH with the 4 bolts.

      Момент затяжки
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }
  12. INSTALL MULTI-MODE MANUAL TRANSAXLE ASSEMBLY

    1. Check that the 2 knock pins are installed on the engine assembly before installing the multi-mode manual transaxle assembly.

      A012KN3
    2. Align the input shaft with the clutch disc and install the multi-mode manual transaxle to the engine assembly.

      A012LSFN01
    3. Install the 8 bolts.

      Момент затяжки
      Bolt A for Flange Bolt
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
      Bolt A for Bolt with Washer
      33 N*m  { 337 kgf*cm, 24 ft.*lbf }
      Bolt B
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
      Note:
      • Make sure that the wire harness or similar items are not pinched between the contact surfaces.

      • Do not forcibly pry on the multi-mode manual transaxle assembly when installing it to the engine assembly.

      • Do not apply excessive force to the multi-mode manual transaxle assembly as this will break the input shaft.

      • Make sure that the knock pins fit securely into the holes when installing the multi-mode manual transaxle assembly to the engine assembly.

      • Make sure that the contact surfaces of the engine assembly and multi-mode manual transaxle assembly are flat against each other before tightening the bolts.

  13. CONNECT WIRE HARNESS

    1. Install the wire harness to the multi-mode manual transaxle assembly with the nut and bolt.

      Момент затяжки
      Nut
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      Bolt
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
    2. Connect the 2 clamps.

    3. Install the wire harness with the 3 clamps.

    4. Connect the 2 connectors to the select stroke sensor and park/neutral position switch assembly.

  14. INSTALL NO. 1 AIR TUBE

    1. Install the No. 1 air tube and tighten the hose clamp.

      A012H4YC01
      *a Hose Clamp
      Момент затяжки
      6.5 N*m  { 66 kgf*cm, 58 in.*lbf }
      Note:

      One minute after tightening the hose clamp, check that residual torque is 3.2 N*m (33 kgf*cm, 28 in.*lbf) or more.

    2. Install the 4 bolts.

      Момент затяжки
      Bolt A
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
      Bolt B
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
      Bolt C
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }
    3. Connect the wire harness clamp.

  15. INSTALL STARTER ASSEMBLY

    Click hereНажмите здесь

  16. TEMPORARILY TIGHTEN REAR ENGINE MOUNTING INSULATOR

    Click hereНажмите здесь

  17. TEMPORARILY TIGHTEN FRONT ENGINE MOUNTING INSULATOR

    Click hereНажмите здесь

  18. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

    Click hereНажмите здесь

  19. PERFORM INITIALIZATION OF MULTI-MODE MANUAL TRANSAXLE SYSTEM

    Click hereНажмите здесь

  20. PERFORM LEARNING OF MULTI-MODE MANUAL TRANSAXLE SYSTEM

    Click hereНажмите здесь

  21. PERFORM SYNCHRONIZATION POSITION CALIBRATION

    Click hereНажмите здесь