ДВИГАТЕЛЬ В СБОРЕ УСТАНОВКА

PROCEDURE

  1. INSTALL ENGINE HANGERS

    Click hereНажмите здесь

  2. REMOVE ENGINE FROM ENGINE STAND

    1. Using a chain block and engine sling device, secure the engine assembly.

      Note:
      • Adjust the angle of the sling device carefully to prevent the engine assembly or engine hangers from deforming or becoming damaged.

      • Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.

    2. Remove the engine assembly from the engine stand.

  3. INSTALL FLYWHEEL SUB-ASSEMBLY

    1. Hold the crankshaft pulley with SST.

      A012KWJN02
      SST
      09213-58014   ( 91551-80840 )
      09330-00021
    2. Using a T55 "TORX" socket wrench, install the flywheel sub-assembly with 8 new bolts and uniformly tighten the bolts in several steps in the sequence shown in the illustration.

      A012JNEN01
      Момент затяжки
      70.6 N*m  { 720 kgf*cm, 52 ft.*lbf }
      Note:
      • Do not reuse the flywheel sub-assembly installation bolts.

      • Be sure to check the tightening torque within 5 minutes of installation.

      • Do not impact or damage the flywheel sub-assembly installation bolts. Be sure to handle them carefully.

      • Make sure there is no oil on the bolts.

      Tip:

      Make sure that the seating surface of the flywheel sub-assembly installation bolts and installation surfaces of the crankshaft and flywheel sub-assembly are free from oil and foreign matter.

  4. INSTALL CLUTCH DISC ASSEMBLY

    Click hereНажмите здесь

  5. INSTALL CLUTCH COVER ASSEMBLY

    Click hereНажмите здесь

  6. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

    Click hereНажмите здесь

  7. INSTALL MANUAL TRANSAXLE ASSEMBLY

    Click here Нажмите здесь

  8. INSTALL ENGINE WIRE

    1. Install the engine wire to the engine assembly with transaxle.

  9. INSTALL STIFFENER PLATE LH

    Click here Нажмите здесь

  10. INSTALL STIFFENER PLATE RH

    Click here Нажмите здесь

  11. INSTALL OIL PAN INSULATOR

    Click here Нажмите здесь

  12. INSTALL STARTER ASSEMBLY

    Click hereНажмите здесь

  13. INSTALL NO. 1 AIR TUBE

    Click here Нажмите здесь

  14. CONNECT ENGINE WIRE

    Click here Нажмите здесь

  15. INSTALL ENGINE MOUNTING INSULATOR LH

    Tip:

    Perform this procedure only when replacement of the engine mounting insulator LH is necessary.

    1. Install the engine mounting insulator LH with the 4 bolts.

      Момент затяжки
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
  16. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

    Tip:

    Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.

    1. Install the engine mounting insulator sub-assembly RH with the 3 bolts.

      Момент затяжки
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
    2. Connect the cooler pipe clamp to the engine mounting insulator sub-assembly RH.

    3. Install the cooler pipe clamp bracket to the engine mounting insulator sub-assembly RH with the bolt.

      Момент затяжки
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }
    4. Connect the cooler piping clamp to the engine mounting insulator sub-assembly RH.

    5. Connect the radiator reservoir tank assembly with the 2 bolts.

      Момент затяжки
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
  17. TEMPORARILY TIGHTEN REAR ENGINE MOUNTING INSULATOR

    Tip:

    Perform this procedure only when replacement of the rear engine mounting insulator is necessary.

    1. Temporarily install the rear engine mounting insulator to the rear engine mounting bracket with the bolt.

  18. TEMPORARILY TIGHTEN FRONT ENGINE MOUNTING INSULATOR

    Tip:

    Perform this procedure only when replacement of the front engine mounting insulator is necessary.

    1. Temporarily install the front engine mounting insulator to the front engine mounting bracket with the through bolt and nut.

  19. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

    1. Set the engine assembly with transaxle on the engine lifter.

      Note:

      Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.

    2. Operate the engine lifter and lift the engine assembly with transaxle to the position where the engine mounting insulator LH and engine mounting insulator sub-assembly RH can be installed.

      ОСТОРОЖНО

      Do not raise the engine assembly with transaxle more than necessary. If the engine assembly with transaxle is raised excessively, the vehicle may also be lifted up.

      Note:

      While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.

      • Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

      • While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.

    3. Install the engine mounting insulator LH with the through bolt and nut.

      Момент затяжки
      56 N*m  { 571 kgf*cm, 41 ft.*lbf }
      Tip:

      When tightening the through bolt, keep the nut from rotating.

    4. Install the engine mounting insulator sub-assembly RH with the 2 bolts and 2 nuts.

      A012KITC01
      *a Nut A
      *b Nut B
      Момент затяжки
      Bolt and Nut A
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
      Nut B
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }
    5. Install the front crossmember sub-assembly with the 4 bolts.

      Момент затяжки
      96 N*m  { 979 kgf*cm, 71 ft.*lbf }
    6. Connect the front engine mounting insulator to the front crossmember sub-assembly with the 2 bolts.

      Момент затяжки
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
  20. REMOVE ENGINE HANGER

    1. Remove the 2 bolts and No. 1 engine hanger and No. 2 engine hanger.

  21. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

    Click here Нажмите здесь

  22. INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH

    Click here Нажмите здесь

  23. INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

    Tip:

    Perform the same procedure as the LH side.

  24. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

    Click here Нажмите здесь

  25. INSTALL FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT (w/ Reinforcement)

    Click here Нажмите здесь

  26. FULLY TIGHTEN REAR ENGINE MOUNTING INSULATOR

    1. Fully tighten the rear engine mounting insulator through bolt.

      Момент затяжки
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
  27. FULLY TIGHTEN FRONT ENGINE MOUNTING INSULATOR

    1. Fully tighten the front engine mounting insulator through bolt and nut.

      Момент затяжки
      85 N*m  { 867 kgf*cm, 63 ft.*lbf }
      Tip:

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured

  28. INSTALL FRONT DRIVE SHAFT ASSEMBLY

    Click hereНажмите здесь

  29. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    Click here Нажмите здесь

  30. INSTALL FRONT CENTER FLOOR BRACE SUB-ASSEMBLY

    Click here Нажмите здесь

  31. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

    Click here Нажмите здесь

  32. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

    Click here Нажмите здесь

  33. INSTALL COLUMN HOLE COVER SILENCER SHEET

    Click here Нажмите здесь

  34. CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

    1. Connect the clutch release cylinder assembly and flexible hose bracket with the 5 bolts.

      A012H95C02
      *a Bolt A
      *b Bolt B
      Момент затяжки
      Bolt A
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      Bolt B
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }
  35. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

    1. Install the transmission control cable assembly to the rear engine mounting insulator with the bolt.

      Момент затяжки
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    2. Install the transmission control cable assembly to the control cable bracket with 2 new clips.

      A012LJ1
    3. Install the transmission control cable assembly to the manual transaxle assembly with the 2 clips.

      A012H63
  36. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY (w/ Air Conditioning System)

    Click hereНажмите здесь

  37. CONNECT DISCHARGE HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

    Click hereНажмите здесь

  38. CONNECT SUCTION HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

    Click hereНажмите здесь

  39. INSTALL V-RIBBED BELT

    Click hereНажмите здесь

  40. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

    Click hereНажмите здесь

  41. INSTALL INJECTOR DRIVER

    Click hereНажмите здесь

  42. CONNECT NO.2 RADIATOR HOSE

    1. Connect the No. 2 radiator hose to the water inlet housing and slide the clip to secure it.

  43. CONNECT WATER BY-PASS HOSE

    1. Connect the water by-pass hose to the water inlet pipe and slide the clip to secure it.

  44. INSTALL INTERCOOLER AIR HOSE

    Click hereНажмите здесь

  45. CONNECT NO. 1 RADIATOR HOSE

    1. Connect the No. 1 radiator hose to the cylinder head sub-assembly and slide the clip to secure it.

  46. CONNECT INLET HEATER WATER HOSE

    1. Connect the inlet heater water hose to the cylinder head sub-assembly and slide the clip to secure it.

  47. CONNECT OUTLET HEATER WATER HOSE

    1. Connect the outlet heater water hose to the cylinder head sub-assembly and slide the clip to secure it.

  48. CONNECT VACUUM PUMP HOSE

    1. Connect the vacuum pump hose to the cylinder head sub-assembly and slide the clip to secure it.

  49. CONNECT HOSES AND CONNECTORS

    1. Connect the ECM connector and lower the lever.

      A012JK1
      Note:
      • When connecting the connector, make sure that dirt, water and other foreign matter is not stuck between the connector and ECM.

      • Make sure that the lever is securely lowered.

    2. Install the air cleaner bracket with the fuel filter support and glow plug relay assembly with the 5 bolts.

      Момент затяжки
      Bolt A
      17.5 N*m  { 178 kgf*cm, 13 ft.*lbf }
      Bolt B
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }
      A012FILN01
    3. Engage the 2 clamps to the air cleaner bracket.

    4. Connect the No. 3 engine wire to the manual transaxle assembly with the bolt.

      Момент затяжки
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
    5. Connect the wire harness to the engine room relay block with the 2 claws. Then install it with the 2 nuts and 3 connectors.

      Момент затяжки
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
    6. Install the No. 1 engine room relay block cover to the engine room relay block.

  50. INSTALL FUEL FILTER ASSEMBLY

    Click hereНажмите здесь

  51. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    1. Install the air cleaner case sub-assembly with the 3 bolts.

      Момент затяжки
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }
    2. install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.

  52. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    1. Connect the air cleaner hose and slide the clip to secure it.

    2. Lock the 2 lock clamps to install the air cleaner cap sub-assembly.

    3. Connect the No. 2 ventilation hose and slide the clip to secure it.

    4. Connect the mass air flow meter connector.

  53. INSTALL NO. 3 AIR HOSE

    Click hereНажмите здесь

  54. CONNECT NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY

    1. Connect the No. 2 vacuum transmitting hose assembly to the intake manifold and slide the clip to secure it.

  55. INSTALL BATTERY CARRIER BRACKET SUB-ASSEMBLY

    1. Install the battery carrier bracket sub-assembly with the 4 bolts.

      Момент затяжки
      18.5 N*m  { 189 kgf*cm, 14 ft.*lbf }
    2. Connect the 2 clamps and engine wire to the battery carrier bracket sub-assembly.

  56. INSTALL BATTERY

    1. Install the battery tray to the battery carrier bracket sub-assembly.

    2. Install the battery insulator and battery.

    3. Install the battery clamp sub-assembly and battery clamp bolt with the bolt and nut.

      Момент затяжки
      Bolt
      16.5 N*m  { 168 kgf*cm, 12 ft.*lbf }
      Nut
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }
    4. Connect the positive (+) cable to the positive (+) battery terminal with the nut.

      Момент затяжки
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
  57. INSTALL DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

    Click hereНажмите здесь

  58. ADD MANUAL TRANSAXLE OIL

    Click hereНажмите здесь

  59. INSPECT FOR MANUAL TRANSAXLE OIL LEAK

    Click hereНажмите здесь

  60. ADD ENGINE OIL

    Click hereНажмите здесь

  61. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    1. Connect the negative (-) cable to the negative (-) battery terminal.

      Момент затяжки
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected

      Click here Нажмите здесь

  62. BLEED FUEL SYSTEM

    Click hereНажмите здесь

  63. ADD ENGINE COOLANT

    Click hereНажмите здесь

  64. PERFORM REGISTRATION

    1. Perform registration of the injector compensation codes.

      Click hereНажмите здесь

    2. Perform registration of the pilot quantity learning.

      Click hereНажмите здесь

  65. PERFORM INITIALIZATION

    1. Perform initialization of the crank time compensation reset function.

      Click hereНажмите здесь

  66. INSPECT FOR OIL LEAK

    Click hereНажмите здесь

  67. INSPECT FOR COOLANT LEAK

    Click hereНажмите здесь

  68. INSPECT FOR FUEL LEAK

    Click hereНажмите здесь

  69. INSPECT FOR EXHAUST GAS LEAK

    Click here Нажмите здесь

  70. INSTALL REAR ENGINE UNDER COVER LH

    1. Install the rear engine under cover LH with the 5 clips.

  71. INSTALL REAR ENGINE UNDER COVER RH

    1. Install the rear engine under cover RH with the 5 clips.

  72. INSTALL FRONT NO. 3 ENGINE UNDER COVER

    Click here Нажмите здесь

  73. INSTALL CENTER NO. 4 ENGINE UNDER COVER (w/ Cover)

    1. Install the center No. 4 engine under cover with the 2 clips.

  74. INSTALL NO. 1 ENGINE UNDER COVER

    1. Install the No. 1 engine under cover with the 11 clips and 6 bolts.

  75. INSTALL FRONT LOWER BUMPER ABSORBER

    Click here Нажмите здесь

  76. INSTALL NO. 1 ENGINE COVER

    1. Engage the 4 clips to install the No. 1 engine cover.

      Note:
      • Be sure to engage the clips securely.

      • Do not apply excessive force or hit the No. 1 engine cover to engage the clips. This may cause the No. 1 engine cover to break.

  77. INSTALL NO. 2 RADIATOR AIR GUIDE

    1. Install the No. 2 radiator air guide with the 7 clips.

  78. INSTALL OUTER COWL TOP PANEL

    Click here Нажмите здесь

  79. INSTALL FRONT WHEELS

    Click here Нажмите здесь

  80. INSPECT ENGINE IDLE SPEED

    Click hereНажмите здесь

  81. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFC-134a(R134a))

    Click hereНажмите здесь

  82. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFO-1234yf(R1234yf))

    Click hereНажмите здесь

  83. WARM UP ENGINE (for HFC-134a(R134a))

    Click hereНажмите здесь

  84. WARM UP ENGINE (for HFO-1234yf(R1234yf))

    Click hereНажмите здесь

  85. INSPECT FOR REFRIGERANT LEAK (for HFC-134a(R134a))

    Click hereНажмите здесь

  86. INSPECT FOR REFRIGERANT LEAK (for HFO-1234yf(R1234yf))

    Click hereНажмите здесь

  87. ADJUST FRONT WHEEL ALIGNMENT

    Click here Нажмите здесь

  88. CHECK ABS SPEED SENSOR SIGNAL

    Click hereНажмите здесь